? ratings from 25 a to 90 a @ 48-530 vac ? scr output for heavy industrial loads ? zero voltage or instantaneous turn-on outputs ? ul/csa/vde approved, ce compliant to en60950-1 ? improved sems screw and washer ? redesigned housing with anti-rotation barriers for generation 3 datasheet click here ? ac or dc control ? direct bond copper substrate ? emc compliant to level 3 ? direct power lead frame ? epoxy free design series 1 480 vac product selection 90 a 75 a 50 a 25 a control voltage 4-32 vdc d4825 d4850 d4875 d4890 90-280 vac a4825 a4850 a4875 a4890 available options control voltage a: 90-280 vac d: 4-32 vdc rated load current 25: 25 amps 50: 50 amps 75: 75 amps 90: 90 amps operating voltage 48: 48-530 vac termination blank: screw f: quick connect (1) (up to 50 amps) k: hex standoffs (2) 25 a thermal pad blank: not included h: included 48 k h s snubber blank: not included s: included switching type blank: zero voltage turn-on -10: instantaneous turn-on (3) -10 output specifications (4) 90 a 75 a 50 a 25 a description operating voltage (47-440hz) [vrms] (5) 48-530 48-530 48-530 48-530 transient overvoltage [vpk] 800 800 800 800 maximum off-state leakage current @ rated voltage [marms] (6) 1 1 1 1 minimum off-state dv/dt @ maximum rated voltage [v/sec] 500 500 500 500 maximum load current [arms] (2)(7) 25 50 75 90 minimum load current [marms] 150 150 150 150 maximum 1 cycle surge current (50/60hz) [apk] 239/250 597/625 954/1000 1145/1200 maximum on-state voltage drop @ rated current [vrms] 1.15 1.15 1.15 1.15 thermal resistance junction to case (rjc) [c/w] maximum 1/2 cycle i2 t for fusing (50/60hz) [a2 sec] 0.8 0.45 0.3 0.27 285/259 1770/1621 4555/4150 6560/5976 minimum power factor (at maximum load) 0.5 0.5 0.5 0.5 input specifications (4) description d48xx a48xx control voltage range 4-32 vdc 90-280 vrms (60hz) maximum reverse voltage -32 vdc - minimum turn-on voltage 4.0 vdc (8) 90 vrms must turn-off voltage 1.0 vdc 10 vrms minimum input current 7.0 ma 5.0 ma maximum input current 12 ma 10 ma nominal input impedance current regulated current regulated maximum turn-on time [msec] 1/2 cycle (9) 20 maximum turn-off time [msec] 1/2 cycle 30 required for valid part number for options only and not required for valid part number not all part number combinations are available. contact crydom technical support for information on the availability of a specific part number. * do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount
general specifications parameters description dielectric strength, input/output/base (50/60hz) 4000 vrms minimum insulation resistance (@ 500 vdc) 10 9 ohm maximum capacitance, input/output 8 pf ambient operating temperature range -40 to 80 c ambient storage temperature range -40 to 125 c weight (typical) 2.6 oz (74.9 g) housing material 94 v-0 baseplate material aluminum input terminal screw torque range (in-lb/nm) 13-15 /1.5-1.7 load terminal screw torque range (in-lb/nm) 18-20 / 2.0-2.2 ssr mounting screw torque range (in-lb/nm) 18-20 / 2.0-2.2 input/load terminal screw torque range (in-lb/nm) (2) w/?k? option 8-10 / 0.9-1.13 (4) wiring diagram ac v load (11) 1 ( ) 2 ( ) 1 output 2 s oli d s t a t e r ela y 4 input 3 4 (? / ) 3 (+ / ) recommended wire sizes terminals wire size (solid / stranded) wire pull-out strength (lb)[n] input output 24 awg (0.2 mm 2 ) / 0.2 [minimum] 2 x 12 awg (3.3 mm 2 ) / 3.3 [maximum] 20 awg (0.5 mm 2 ) / 0.518 [minimum] 2 x 10 awg (5.3 mm 2 ) / 5.3 2 x 8 awg (8.4 mm 2 ) / 8.4 [maximum] 10 [44.5] 90 [400] 30 [133] 110 [490] 90 [400] input current vs input voltage standard regulated dc input input current (ma) 25 20 15 10 5 0 0 5 10 15 20 25 30 dc input voltage equivalent circuit block diagrams diagram: series 1 dc +dc - dc ac trigger circuit current limiter ac 3 4 2 1 (12) diagram: series 1 ac ac ac ac trigger circuit current limiter ac 3 4 2 1 ac/dc converter (12) humidity per iec60068-2-78 93% non-condensing mtbf (mean time between failures) at 40c ambient temperature (10) 11,641,553 hours (1,328 years) mtbf (mean time between failures) at 60c ambient temperature (10) 7,210,376 hours (823 years) do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount input/output terminal screw thread size #6-32 unc / #8-32 unc
mechanical specifications (4) general notes screw termination 1 output 2 s oli d s t a t e r ela y 4 input 3 1.1 [27.9] 0.49 [12.4] mounting hole/slot 0.19 [4.9] dia. 0.89 [22.6] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] 1.0 [25.4] 1.75 [44.5] hex standoff termination (?k? option) 1.1 [27.9] 0.49 [12.4] mounting hole/slot 0.19 [4.9] dia. 1.04 [26.4] 1.88 [47.6] 1.70 [43.2] 2.25 [57.3] 1.0 [25.4] 1.75 [44.5] 0.93 [23.6] (4 places) 1.0 [25.4] (2 places) 1 output 2 s oli d s t a t e r ela y 4 input 3 (2) quick connect termination (?f? option) - up to 25 amp (1) 1 output 2 s oli d s t a t e r ela y 4 input 3 mounting hole/slot 0.19 [4.9] dia. 1.58 [40.2] 0.49 [12.4] faston terminal (13) 0.25 x 0.032 (2 places) 1.31 [33.4] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] 1.40 [35.6] 1.75 [44.5] faston terminal (13) 0.187 x 0.020 (2 places) 1.25 [31.8] quick connect termination (?f? option) - up to 50 amp (1) 1 4 2 3 s oli d s t a t e r ela y output input mounting hole/slot 0.19 [4.9] dia. 1.58 [40.2] 0.49 [12.4] faston terminal (13) 0.25 x 0.032 (4 places) 1.31 [33.4] 1.88 [47.6] 1.7 [43.2] 2.25 [57.3] 1.40 [35.6] 1.75 [44.5] faston terminal (13) 0.187 x 0.020 (2 places) 1.25 [31.8] 0.63 [16.0] 0.45 [11.4] (2 places) tolerances: 0.02 in / 0.5 mm all dimensions are in: inches [millimeters] for additional information or speci?c questions, contact crydom technical support. do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount (1) single pair (up to 25 a) double pair* (50 a model only). *caution: user must connect to both pairs. (2) option ?k? is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm), and loads rated up to 50 amps. for higher load currents, the ?k? standoff temperature must not exceed 105c. for additional application assistance please contact crydom technical support. (3) instantaneous turn-on not recomended for capacitive loads. use zero turn-on only. (4) all parameters at 25c unless otherwise speci?ed. (5) for ?s? option, operating voltage frequency is 47-63hz. (6) for parts with option ?s? maximum leakage current is 10ma. (7) heat sinking required, see derating curves. (8) increase minimum voltage by 1v for operations from -20 to -40c. (9) turn-on time for instantaneous turn-on versions is 0.02 msec (dc control models). (10) all parameters at 50% power rating and 100% duty cycle (contact crydom tech support for detailed report). (11) load can be wired to either ssr output terminal 1 or 2. (12) elective internal snubber, ?s? option. (13) mechanical dimensions vary from g3 models.
surge current information 0 50 100 150 200 250 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 25 a 0 100 200 300 400 500 600 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 50 a 0 100 200 400 300 500 600 700 900 800 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 75 a 0 150 450 300 600 750 900 1200 1050 0.0 1 0.1 1 10 surge current ( a mp) surge duration ( s ecs) 90 a non repetitive peak surge current at tj initial 40oc. thermal derate information 25 20 15 10 5 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 25 a 1.5oc/w 2oc/w 3oc/w 50 40 30 20 10 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 50 a 0.7oc/w 1oc/w 1.5oc/w 2oc/w 75 60 45 30 15 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 75 a 0.5oc/w 0.7oc/w 1oc/w 1.5oc/w 80 90 70 50 30 10 60 40 20 20 30 40 50 60 70 80 0 ambient temperature (oc) load current (amps) 90 a 0.5oc/w 0.7oc/w 1oc/w 1.5oc/w do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount
agency approvals en60950 : meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: designed in accordance with the requirements of iec 62314 iec 61000-4-2 : electrostatic discharge ? level 3 iec 61000-4-4 : electrically fast transients ? level 3 iec 61000-4-5 : electrical surges ? level 3 iec 60068-2-6 : vibration 0.33mm and 0.75 mm amplitude over 10-55 hz iec 60068-2-27 : shock resistance 15g/11ms e116949 lr81689 10143 ug acc e s o r i e s recommended accessories cover hardware kit heat sink part no. thermal resistance [oc/w] lug terminal thermal pad ks101 hk1 hk4 trm1 trm6 hsp-1 hsp-2 hs501dr hs301 / hs301dr hs251 hs202 / hs202dr hs201 / hs201dr hs172 hs151 / hs151dr hs122 / hs122dr hs103 / hs103dr hs101 hs073 hs072 hs053 hs033 hs023 5.0 3.0 2.5 2.0 2.0 1.7 1.5 1.2 1.0 1.0 0.7 0.7 0.5 0.36 0.25 rev. 041116 part number: ks101 clear plastic cover compatible with all new s1 designs. safety covers provide added protection from electric shock when installing or checking equipment. protective cover hardware kit part number: hk4 bag with 2 square brass accessories and 2 screw 8-32 x 5/8 for output. used to mount tmr1 lug terminals. new accessories! protective cover & hardware kits do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount
do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount danger / peligro / danger /gefahr / pericolo / h a z a r d o f e l e ct ric s ho ck, e x p l o s io n, o r a r c flash. ? di s c o n n e c t a l l p o w e r b e f o r e i n s ta l l i n g o r wo r k i n g w i t h th i s equipment. ? v e r i f y a l l c o n n e c ti o n s a n d r e p l a c e a l l c o v e r s b e f o r e tu r n i n g o n p o w e r . f a ilu r e t o f o llo w t h e s e in s t r u c t io n s w ill r e s u lt in d e a t h o r s e r io u s in ju r y . rie s g o de de s c a rg a e l e ct ric a o e x p l o s io n. ? de s c o n e c ta r to d o s l o s s u m i n i s tr o s d e e n e r g i a a e s te e q u i p o a n t e s d e tr a b a j a r c o n e s te equipo. ? v e r i f i c a r to d a s l a s conexiones y colocar todas l a s ta p a s antes d e energizer el e q u i p o . e l in c u m p lim ie n t o d e e s t a s in s t r u c c io n e s p u e d e p r o v o c a r la m u e r t e o le s io n e s s e r ia s . ris q u e de de s ch a rg e e l e ct riq ue o u explosion ? e te i n d r e to u te s l e s s o u r c e s d ' n e r g i e d e c e t a p p a r e i l a v a n t d e tr a v a i l l e r d e s s u s d e c e t a p p a r e i l ? vrifier tous connections, et remettre tous couverts en olace avant de mettre sous de n o n-s u iv i d e c e s in s t r u c t io n s p r o v o q u e r a la m o r t o u d e s l s io n s srieuses s r i e u s e s. g e f a hr e in e s e l e kt ris ch e n s chl a g e s o de r e ine r e x p l o s io n. ? s te l l e n s i e j e g l i c h e n s tr o m a b , d e r d i e s e s g e r ? t v e r s o r g t, bevor s i e a n dem g e r ? t arbeiten d u r c h f h r e n ? v o r d e m dr e h e n a u f e n e r g i e a l l e a n s c h l s s e b e r p r f e n u n d a l l e a b d e c k u n g e n e r s e t z e n. un t e r la s s u n g d ie s e r a n w e i s u n g e n k ? n n e n z u m t o d e o d e r z u s c h w e r e n v e r le t z u n g e n f h r e n. ris chio di s co s s a e l e t t ric a o de l l ?e s p l o s ione. ? s p e n g a tu tt a l ' a l i m e n ta z i o ne c h e f o r n i s c e q u e s ta a p p a r e c c h i a t ura p r i m a d i lavorare a questa a p p a r e c c h i a t ura ? v e r i f i c a r e t u tti i c o l l e g a m e n ti e s o s ti tu i r e tu tte l e coperture p r i m a d e l l ?accensione l ' o m is s io n e d i q u e s t e istruzioni p r o v o c h e r l a m o r t e o le s io n i s e r i e ? ? ? ? ? ?? ??? ? ??? ? warning / avertissement / warnung /advertencia / avvertenza / risk of material damage and hot enclosure ? the product's side panels may be hot, allow the product to cool before touching. ? follow proper mounting instructions including torque values. ? do not allow liquids or foreign objects to enter this product. failure to follow these instructions can result in serious injury, or equipment damage. risque de dommage materiel et de surchauffe du boitier ? les panneaux latraux du produit peuvent tre chauds. laisser le produit refroidir avant de le toucher. ? respecter les consignes de montage, et notamment les couples de serrage. ? ne pas laisser pntrer de liquide ni de corps trangers l'intrieur du produit. le non-respect de cette directive peut entra?ner, des lsions corporelles graves ou des dommages matriels. die nichtbeachtung dieser anweisung kann k?rperverletzung oder materialsch?den zur folge haben. gefahr von materialsch?den und geh?useerhitzung ? die seitenw?nde k?nnen hei? sein. lassen sie das produkt abkhlen, bevor sie es berhren. ? beachten sie die montageanweisungen, ? fhren sie keine flssigkeiten oder fremdk?rper in das produkt ein. si no se respetan estas precauciones pueden producirse graves lesiones, da?os materiales. riesgo de da?os materiales y de sobrecalentamiento de la unidad ? los paneles laterales del producto pueden estar calientes. esperar que el producto se enfre antes de tocarlo. ? respetar las instrucciones de montaje, y en particular los pares de apretado. ? no dejar que penetren lquidos o cuerpos extra?os en el producto. la mancata osservanza di questa precauzione pu causare gravi rischi per l'incolumit personale o danni alle apparecchiature. rischio di danni materiali e d'involucro caldo ? i pannelli laterali dell'apparecchio poss ono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. ? seguire le istruzioni di montaggio corrette. ? non far entrare liquidi o oggetti estranei in questo apparecchio. ??? ??? ???? ? ?????? ? ? ?????? ? ???
annex - e n v i romental information the environmental information disclosed in this annex including the eip pollution logo are in compliance w i th people?s republic of china electronic industr y standard sj/t11364 ? 2006, marking for c ontrol of pollution caused by electronic information products. part name toxic or hazardous substance and elements lead mercury cadmium hexavalent polybrominated polybrominated (pb) (hg) (cd) chromium (cr (vi)) biphenyls (pbb) diphenyl ethers (pbde) semiconductor die solder - ? ?????????????? sj/t11364 - 2006, ?????? ??? ? ? (pb) (hg) (cd) (cr (vi)) (pbb) (pbde) ?? ? 50 do not forget to visit us at: www.crydom.com copyright ? 2016 crydom inc. specifications subject to change without notice. datasheet panel mount
|
